DTS GT200 review: Fast and beautiful FPV drone

The fact that, after only 2 hours we published the article about the DTS GT200 drone, its authorized dealer contacted us regarding the possibility to review it, gives us confidence that we are doing a good job here on FirstQuadcopter. We will continually strive, during 2019, to provide even more exiting drone news and honest quadcopter reviews.

Zonda Hobby’s portfolio has 3 major product brands: “E-sky”, “DTS” and “GWY”. On their website you can find couple of RC helis and two racing drones. Both, DTS GT200 and DTS Q220 are offered in RFR aka PNP versions (no radio & battery).

Built around a highly integrated flight system (flight controller, ESC and VTX), the DTS GT200 quadcopter has a very clean aspect. Unfortunately for lazy pilots, the radio receiver is not integrated into the GWY007731 main controller unit and they will need to make personally the installation. According to your radio system, you can opt for DSM or SBUS connector cable. The main difference between the cables is that, while the first one powers the receiver with 3.3V, the second one with 5V.

DTS GT200 review: Introduction

Zonda Hobby DTS GT200 drone review

Disclosure: I received this FPV drone from ZondaHobby (Rainbow Model Technology) in order to test it and make an in-depth review. Although the product was offered for free, all opinions in this review remain my own and I was in no way influenced by my partner!

Every time I receive a new drone, I get enthusiast like a 5 year old boy on Christmas Eve. I can’t wait to get home and unpack my new toy. The DTS GT200 comes nicely packed in a black box. Besides the drone, I found the following accessories: spare canopy, 2 sets of DTS 5046 props, GWY 5.8G circular polarized antenna, DSM radio cable, 2 radio receiver antenna protector tubes, DTS stickers, 3M adhesive taps, lots of tools (screwdriver, hex wrenches and prop nuts key) and user manual.

DTS GT200 drone review: Accessories

In-depth analysis

For sure, holding the ZDGB DTS GT200 in my hand looks at least as good like in the advertising photos. I could say that is beautifully manufactured like a Swiss made watch :). It has super clean build with well organised wires. Moreover, all the electronic parts are well protected. While all the frame parts, including the propellers, are black, the motors and the FPV camera have silver color. The nice black/silver contrast grants a very professional look for DTS GT200 drone. Weighting about 372 grams, it is heavier than similar sized FPV drones.

As I previously mentioned, the brain & heart of the GT200 quad is an all-in-one flight system. In order to ensure good heat dissipation, it has an aluminium heat sink on top. VTX buttons (CH & Band) and micro USB port are on left side of the main unit. As it should be normal, battery cable with XT60 plug and FPV antenna pigtail are on rear. The antenna mount has a spring which should reduce the shocks during crashes.

DTS GT200 drone review: Antenna mount

In order to allow stable take-off, the DTS GT200 has some kind of landing skid made from a carbon fiber plate and self-adhesive foam. The skid also severs to secure firmly the LIPO battery under the drone. Both, battery contact plates are padded with non-slip rubber.

The RunCam Eagle 2 Pro camera is well protected by the aluminium canopy. You can adjust the angle of the camera according to your flight style. On top of the canopy you can attach a second DVR camera. My Foxeer Legend 3 fits just perfectly.

DTS GT200 drone review: Second camera

At the end of each 4mm arm there is a DTS 2500K bruhless motor. During crashes they are protected by carbon fiber motor guards.

DTS GT200 main parts

  • 200mm sized carbon fiber frame (DTS007724);
  • Aluminium canopy (DTS007727);
  • Motor guards (DTS007725);
  • All-in-one flight system – Flight controller, ESC & VTX (GWY007731);
  • 2206-2500K bruhless motors (DTS007732);
  • DTS 5046 3-leaf propellers (DTS007729);
  • RunCam Eagle 2 Pro w/ 2.1mm lens (GWY007734).

DTS GT200 review: Camera, FPV and OSD

Like I already mentioned in the introduction part of my ZDHB GT200 review, DTS opted to use a RunCam Eagle 2 Pro (GWY edition) camera which doesn’t just have brilliant image quality, but also very low latency. Eagles 2’s “Pro” version comes with built-in OSD (battery voltage, timer and pilot name) and on-board microphone.

DTS GT200 drone review: Camera

In case you want to fine tune the camera’s settings, you will need a OSD keyboard.

By default, craft name, elapsed flight time, flight mode and battery voltage OSD values are displayed on the FPV monitor. Of course, you can add more OSD info like virtual horizon and instant current.

DTS GT200 drone review: OSD

The camera is paired with a 5.8G/48CH video transmitter with adjustable broadcast power. According to your needs, you can set 25, 200 or 600mW TX power.

DTS GT200 review review: Flight experience

First off all: Do not power ON the DTS GT 200 with installed propellers till everything is configured properly and double checked. Another important thing is that the DTS GT 200 adopts reversed motor direction, so the propellers need to be installed according to this (check the quick start guide for more details). Also, by default, if you arm the motors they start to spin even at zero throttle.

Although I did these pre-flight steps many times, I’m always excited like the first time. You  know that first successful throttle is very important 🙂

Flight preparation (radio receiver installation & binding)

If you have the luck to own a radio receiver with a compatible plug, the installation process is very easy and can be done in just few minutes. The manufacturer, thought about everything. You have easy access to the radio plug, 3M adhesive tape applied, antenna holder and antenna protector tube. Also, there is enough room for larger receivers like my FrSky XSR 16CH ACCST.

DTS GT200 drone review: Radio receiver

As not everything can be perfect, my receivers’s plug didn’t matched with the one provided with the DTS GT200, so I had to cut it down and solder together the wires. You have 3 wires: black – GND, red – 5V (for SBUS) and white – Signal.

Binding DTS GT200 with Taranis Q X7 transmitter

Firstly, I created a new model on my remote controller and named it “DTS GT200”. After that, under the “Model setup” screen, I set “Internal RF”, operation mode to “D16” and channels number to 16. Finally, I selected the “Bind” option. When the transmitter is entering the “Bind” state, it makes a high-pitched beeping.

DTS GT200 drone review: Transmitter binding

Now, you can plug the battery while you hold down the receiver’s F/S button. Successful binding will be confirmed by solid green light.

Critical BetaFlight settings

If you are completely new in the field, I suggest you to edit only the following settings:

  1. Channel mapping & switch assignment. Here you need to assign switches to arm/disarm motors, to toggle between flight modes and to activate the buzzer. Additionally you can set pre-arm switch (this safety measurement is necessary if you have kids);
  2. OSD values: You can customize telemetry info to your OSD screen.

DTS GT200 drone review: BetaFlight

You can access remotely the BetaFlight OSD menu using the following stick combination: Throttle Mid + YAW Left + Pitch Forward.

How it performs in the air?

First take-off was a nightmare, I almost cut the carpet, my wife was about to kill me :D. While I always suggest to read the drone manual before power ON, somehow I skipped this step. I installed the propellers normally, but the motors have reversed direction. After 30 minutes of guessing which may be the problem for not taking off and just flipping on one side, I took the manual to read it. There is a dedicated page which warns you that the motors have reversed direction and it shows the right order of the props. Switching the props I managed to take-off, finally :).

Updates: Following my suggestion, Zonda Hobby added a “Caution” sticker, which warns about the reversed motors direction.

DTS GT200 review: Motor direction

Although, my flight field was covered by about 20cm of snow and it was windy, I went out for a test flight. For the maiden I used a freshly charged 4s – 1300mAh battery.

Take-off was smooth, but after few flight movements I felt it a bit shaggy and heard a pitched noise. I landed immediately and performed a visual inspection. One of the prop nuts was not tight enough. Two minutes later, fix-it and back in the air. Rest of the flight was smooth and pleasant.

I tried few punch-outs and flips. Although it has good power, I felt it less nimble than my Kopis 2. IMHO, the difference could be due to the weight difference (372 vs 282 grams).

FPV quality is excellent, the RunCam camera makes a good job. It has good response on light level changes and negligible latency. Only slight part of the front propellers are visible in the video feed.

My first flight ended after 6 minutes. Of course, this time could be less if you fly more aggressively.

Price and Availability

The DTS GT200 can be ordered either directly from Zonda Hobby or from other reputable online retailers. Now, you can find it on Bangggood for US$279.32. Don’t forget that you will need to additionally to purchase a compatible radio system (receiver & transmitter) and flight battery.

DTS GT200 drone review: Verdict

Editor’s ratings



    Price/performance ratio



    Build quality



    Camera & FPV & OSD



    Flight performance





Maybe the DTS GT200 is not the cheapest FPV drone in its category but it has one of the best built quality. It is a truly premium product. I liked that it comes with many accessories, including 2 sets of propellers.

The RunCam camera provides excellent image quality and the VTX has a strong signal even on the lowest power setting.

Last but not least, it’s super fast and agile. Even the most skilled pilots will love its flight performance.


User Review

4.45 (20 votes)

News & Trending

Xiaomi FiMI A3 review: Is it worth it?

2023-3-8 11:17:52

News & Trending

Best drone for kids: Eachine E016H review

2023-3-8 11:24:58

0 comment AAuthor MAdministrator
    No Comments Yet. Be the first to share what you think!
Message Message